2013年1月11日星期五

How to remove and install car speaker in 2005-2012 Toyota Tacoma

Toyota Tacoma Speaker Tweeeter Removal & Installation 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 Double Cab, Access Cab & X-Runner

Toyota Tacoma Speaker
1.READ ALL DIRECTIONS and REVIEW PICS BEFORE STARTING!!!

Place your new speaker in the speaker mounts, center and line up your speaker before you start.

It may help to sit in a chair and let the speaker "hang" down. This will allow the speaker to sit flush, making it easier to mark your "drill" holes.

Toyota Tacoma Speaker 2
2.After marking the location for the holes, remove the speaker and drill a pilot hole about 3/8 of an inch deep. Pilot hole should be smaller than screws. DO NOT drill all the way through the mount. If you do not have a drill you can use your screw driver to "force" the screws into the plastic. It is not difficult, but we recommend the speakers not be in place during this step as the screw driver could slip and damage your new speakers.

Toyota Tacoma Speaker Tweeeter Removal & Installation
3.Place the speaker back into the mount and use the pan head screws (silver ones in the pics) to attach the speakers to the mount. Be careful not to let the screwdriver slip and damage your speakers. Do not over tighten the screws.

Toyota Tacoma Speaker Tweeeter Removal & Installation 2
4.Roll down ALL your windows prior to starting the installation.

Remove the sail panel as show above. Simply pull straight out.

Toyota Tacoma Speaker Tweeeter Removal & Installation 3
5.Sail panel removed. Note the white clips stayed in the door. You will want to remove these and attach to the sail panel.

Toyota Tacoma Speaker Tweeeter Removal & Installation 4
6.By gently squeezing and pulling up remove the power window panel.

NOTE: Squeeze on the side of the window panel.

Toyota Tacoma Speaker Tweeeter Removal & Installation 5
7.Press to release the harness lock and pull away from window power panel.

Toyota Tacoma Speaker Tweeeter Removal & Installation 6
8.There are two screws on each door. The first one is located above the "lock". The second is located below handle that you use to close the door. The front doors are covered with a little plastic square. Use the small screwdriver or knife to "gently" pry the square open. They are attached on one side and have a "notch" on the other. You will pry from the notch side. It takes very little force to open the cover so be gentle not to scratch your door panel.

How to remove and install car speaker in 2005-2012 Toyota Tacoma
9.There are two screws on each door. The first one is located above the "lock". The second is located below handle that you use to close the door. The front doors are covered with a little plastic square. Use the small screwdriver or knife to "gently" pry the square open. They are attached on one side and have a "notch" on the other. You will pry from the notch side. It takes very little force to open the cover so be gentle not to scratch your door panel.

How to remove and install car speaker in 2005-2012 Toyota Tacoma 2
10.Use the Phillips to remove the two screws. Mark each screw so you know which one goes on top and which one goes on the bottom.

How to remove and install car speaker in 2005-2012 Toyota Tacoma 3
11.Use the Phillips to remove the two screws. Mark each screw so you know which one goes on top and which one goes on the bottom.

How to remove and install car speaker in 2005-2012 Toyota Tacoma 4
12.After removing the two screws you will pull the panel away from the door. Start below the speaker opening (bottom of the door) and work your way around to the top on. Your fingers should fit and allow you to pull around the speaker area as shown.

How to remove and install car speaker in 2005-2012 Toyota Tacoma 5
13.Gently pull on the panel. NOTE: The part of the door panel that is attached to the window is "hanging". Do NOT pull on the top part of the door panel. Notice the gap between the door and the panel.

How to remove and install car speaker in 2005-2012 Toyota Tacoma 6
14.After you have "popped" out the bottom portion of the door panel you will "lift" the panel upwards to remove it from the door.

How to remove and install car speaker in 2005-2012 Toyota Tacoma 7
15.continued - After you have "popped" out the bottom portion of the door panel you will "lift" the panel upwards to remove it from the door.

car Door panel removed
16.Door panel removed.

car speaker removal
17.Remove the 4 bolts using a 10 MM socket or wrench. The bolts are not very tight.

car speaker removal 2
18.Remove the 4 bolts using a 10 MM socket or wrench. The bolts are not very tight.

toyota speaker installation
19.Remove the 4 bolts using a 10 MM socket or wrench. The bolts are not very tight.

toyota speaker installation 2
20.Remove the 4 bolts using a 10 MM socket or wrench. The bolts are not very tight.

toyota speaker installation 3
21.Remove the wire harness from the speaker.

toyota speaker installation 4
22.Factory speaker ready to be removed.

2005 toyota tacoma speaker removal and installation guide
23.Speaker removal.

2006 toyota tacoma speaker removal and installation guide
24.Install new speakers. If you purchased our entire kit. Use the bolts and washers provided.

2007 toyota tacoma speaker removal and installation guide
25.Before mounting your speaker, plug in the wire harness kit provided in the "kit". If you did not purchase the kit, you will have to cut your factory wires and install plugs to attach the wires to your new speakers. Feed the wires through the small hole in the door and plug into the speakers before you bolt the speakers down. Use the bolts provided in your kit. If you did not purchase the kit you will need to get the proper length bolts to fit.  When mounting your speakers, make sure they do not hit the door, glass or other moving parts. We have tested the mounts with a number of speakers and have not had any problems. However, as mentioned above, make sure to roll your windows down before you start the installation.  Be sure to test your speakers before installing the door panels.

2008 toyota tacoma speaker removal and installation guide
26.Place the panel back on the door and make sure it is "hanging" properly before you attempt to attach the "snaps".

2009 toyota tacoma speaker removal and installation guide
27.Once the door panel is lined up, simply tap the panel into place. You should hear clicks as each "button" snaps back into place.

2010 toyota tacoma speaker removal and installation guide
28.Attach the while clips (removed earlier ) onto the sail panel as shown. Then push back into place.

2011 toyota tacoma speaker removal and installation guide
29.Re-install your window power panel.

0 评论:

Most popular post last week:

Car GPS Navigation Wholesale